Medialink MWN-WAPR300N Spezifikationen

MWN-WAPR300N

MWN-WAPR300N 5 Chapter 3 How to configure your computer’s Ethernet (LAN) connection. (Please note that most computers are

MWN-WAPR300N 6 4. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click “O

MWN-WAPR300N 7  DNS server: You should input the DNS server address provided by your ISP. Otherwise, you can enter 192.

MWN-WAPR300N 8 3. Right click “Local Area Connection” and select “Properties”. 4. Double click” Internet Protocol Versi

MWN-WAPR300N 9 automatically”. Click “OK” to save the configurations. Or if you want to specify a Static IP Address for

MWN-WAPR300N 10 3.2 Log in to the Router 1. To access the Router’s Web-based Utility, launch a web browser such as Inter

MWN-WAPR300N 11 3.3 Fast Internet Access Two kinds of fast access methods are provided on the router’s web-based utility

MWN-WAPR300N 12 default is “password” and you can change it whenever you want. 3.4 Default Wireless Settings Your Mediali

MWN-WAPR300N 13  Gateway: Obtained from ISP, modem, or router.  DNS Server: Obtained from ISP, modem, or router.  A

MWN-WAPR300N 14 4.2 WAN Settings Click “Advanced Settings” > “WAN Settings” to enter the following screen: PPPoE (aD

MWN-WAPR300N Copyright Statement is the registered trademark of Medialink Products, LLC. All the products and product names ment

MWN-WAPR300N 15 times. Otherwise, enter the minutes to be elapsed before you are disconnected from the Internet.  Con

MWN-WAPR300N 16 (optional)  Click “Apply” when finished. Dynamic IP (Via DHCP) If your connection mode is Dynamic IP, i

MWN-WAPR300N 17 or “Static”. If your ISP doesn’t provide the IP address, please select “Dynamic”.  IP Address: Please e

MWN-WAPR300N 18  LAN MAC Address: The Router’s LAN MAC Address, which is unchangeable.  IP Address: The Router’s LAN

MWN-WAPR300N 19 that your ISP connection will work properly.  MAC Address: The MAC Address to be registered with your

MWN-WAPR300N 20 4.6 WAN Speed This page allows you to set the connection speed of the WAN port. It is not recommended to

MWN-WAPR300N 21  Upload/Download: specifies the traffic direction for the selected IP addresses.  Bandwidth Range:

MWN-WAPR300N 22 And then add a download rule as shown in the picture below. 1. Enter 192.168.8.2 in the both IP address

MWN-WAPR300N 23 Download Rule: 4.8 Traffic Statistics Traffic statistics is used to display the bandwidth that LAN dev

MWN-WAPR300N 24  Uplink Rate: The data speed of data sent from the device per second, the unit is KByte/s.  Downlink

MWN-WAPR300N Contents CHAPTER 1 PRODUCT INTRODUCTION ... 1 1.1 PACKAGE CONTENTS ...

MWN-WAPR300N 25 4.10 WAN Medium Type / Range Extender Wired WAN and Wireless WAN Wired WAN: In this mode, a network ca

MWN-WAPR300N 26 How to use Wireless WAN to create a Wireless Bridge from your existing Wireless Router: LAN IP Address:

MWN-WAPR300N 27 Note: The Signal Strengh is displayed in dBm (-). It is not a percentage. Therefore the lowest number is

MWN-WAPR300N 28 Security: The SSID (in this example), Security Mode, Algorithm and Key have been manually entered and e

MWN-WAPR300N 29 Chapter 5 Wireless Settings 5.1 Wireless Basic Settings  Enable Wireless Function: Select to e

MWN-WAPR300N 30 SSID will be isolated from other devices that wirelessly connect to the Secondary SSID. AP Isolation is e

MWN-WAPR300N 31  AP MAC Address: Input the MAC address of another (opposing) wireless router that supports WDS that yo

MWN-WAPR300N 32 Wireless Security: <MUST Match First MWN-WAPR300N> Wireless Working Mode: WDS Bridge Mode DHCP Serv

MWN-WAPR300N 33 5.2 Wireless Security Settings The Medialink router is secured by default using WPA-PSK with AES Alg

MWN-WAPR300N 34  WPS Settings: To enable or disable WPS function. The default is “Enable”.  WPS Mode: PBC (Push-Butt

MWN-WAPR300N 5.2.3 WPA2-PSK (WPA2-PERSONAL) ... 35 5.2.4 WEP ...

MWN-WAPR300N 35  WPA Algorithms: Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standar

MWN-WAPR300N 36 [Advanced Encryption Standard].  Key: Enter the pass phrase that consists of 8-63 ASCII characters

MWN-WAPR300N 37  MAC Address Filter: “Permit” allows the clients in the list to be the only clients to be able to acc

MWN-WAPR300N 38 Chapter 6 DHCP Server 6.1 DHCP Server DHCP (Dynamic Host Control Protocol) is used to assign an IP addr

MWN-WAPR300N 39  Host Name: The name of the device whose IP is allocated by the DHCP server. This name is generated b

MWN-WAPR300N 40 Chapter 7 Virtual Server 7.1 Port Range Forwarding  Start/End Port: Enter the start/end port number wh

MWN-WAPR300N 41 to enable your friends to access to these files on your computer. Suppose that your FTP server or your co

MWN-WAPR300N 42 NOTE: If you set the service port of the virtual server as 80, you must set the Web management port on

MWN-WAPR300N 43  Enable UPnP: Click the checkbox to enable the UPnP. Chapter 8 Security Settings 8.1 Client Filter Se

MWN-WAPR300N 44 end time. The Time cannot cross over midnight.  Day(s): Select the day(s) to run the access policy. T

MWN-WAPR300N 10.7 CHANGE USERNAME/PASSWORD ... 55 10.8 SYSLOG ...

MWN-WAPR300N 45  Filter mode: You can select “Forbid only” or “Permit Only”.  Access Policy: Select a number from the

MWN-WAPR300N 46  Filter Mode: “Forbid only” is the only mode.  Access Policy: Select a number from the drop-down lis

MWN-WAPR300N 47 NOTE: Enter only one domain name or keyword for each access policy. So, if you want to filter multip

MWN-WAPR300N 48  IP Address: Specify the range of the Public IP addresses of the computers on the Internet for remote m

MWN-WAPR300N 49 A static route is a pre-determined pathway that network information must travel to reach a specific host

MWN-WAPR300N 50 Chapter 10 System Tools 10.1 Time Settings This section is to configure the router’s system time. You can

MWN-WAPR300N 51  Main features: 1. Most ISP connections provide a dynamic IP address and the DDNS is used to captu

MWN-WAPR300N 52  Backup Settings: Click the Backup button to back up the router’s settings and select a path to save t

MWN-WAPR300N 53 Click the “Restore” button to restore previous settings. 10.4 Restore to Factory Default This screen

MWN-WAPR300N 54 WARNING: BE SURE TO USE A COMPUTER THAT IS CONNECTED TO THE ROUTER VIA ETHERNET TO ADJUST THE FIRMWARE.

MWN-WAPR300N 1 Chapter 1 Product Introduction Thank you for purchasing the Medialink Wireless 300N Router! This router i

MWN-WAPR300N 55  Reboot the router: Click this button to reboot the router. 10.7 Change Username/Password This sectio

MWN-WAPR300N 56  Refresh: Click this button to update the log.  Clear: Click this button to clear the currently show

MWN-WAPR300N 57 Appendix 1 Glossary Channel: A distinct frequency range within the 2.4 GHz wavelength. There are 11

MWN-WAPR300N 58  Supports hidden SSID function and MAC Address-based access control  Supports WMM to make your audio

MWN-WAPR300N 59 3. The device is telling me that the password I am entering is incorrect. Make sure you are entering the

MWN-WAPR300N 60 3. Click “Wireless Network Configuration” and clear the corresponding wireless configuration file as sho

MWN-WAPR300N 61 2. Click “Manage wireless networks” on the left side of the window. 3. Delete the corresponding configur

MWN-WAPR300N 62 equipment generates uses and can radiate radio frequency energy and, if not installed and used in accorda

MWN-WAPR300N 2 Back panel ports

MWN-WAPR300N 3 Back panel port description

MWN-WAPR300N 4 Chapter 2 Product Installation 1. Please use only the included power adapter to power your router. (NOTE